07-13-2007, 08:07 PM
I use a toilet-paper tube or sometimes empty yoghurt-containers as moulds. For purposes of this document, I shall demonstrate construction using the TP-roll mould; the procedure is basically identical for any other mould you may decide to use. If you use TP-tubes, be sure to tape the bottom ends off well with several layers of duct-tape so the resin doesn't leak out; if you use another container, be sure its deep enough to embed the entire coil-assembly.
[attachment=18]
I like to mix some metal & resin in a separate container & add the goop in stages, poking at it with a stick & tamping it down as I go to avoid air-bubbles. Even so, the bubbles are practically unavoidable; I have found that, while unsightly, if they aren't too big they don't make any significant difference in the device's performance.
First, I'll lay down a good base of the metal & resin, then push the crystal-assembly point-down into the clump & fill the rest of the glop down between the coil-windings---this is where the stick comes in handy---much easier than trying to wind the coil down into the goo.
[attachment=19]
Then, I'll fill the rest of the tube with some more glop, covering the top of the coil as I go, & tamp it down some more (being careful when packing it down that I don't cut through the tape); if you watch it carefully while the resin 'cooks', there will be about a 5 minute widow of time during which you'll be able to see bubbles & smoke percolating up through the already-hardened surface, like a witches' cauldron, & the mould will be hot to the touch. Now wait 4 or 5 hours for the stuff to 'breathe' & harden; if you bring it in too soon, you will overwhelm your household with noxious gasses.
[attachment=20]
Lastly, after peeling off the tape & picking off as much of the resin-spillage as will come, the TB's will still be sticky on the outside, so I cover them with a piece of a grocery-bag & tie them up with fishing-line. This is totally unnecessary in terms of the device's functionality; I just do it to facilitate travel in my jacket-pockets.
[attachment=21]
The outside can be painted, if camoflauge is desired for locations where burying them is impractical.
[attachment=22]
I like to bury them 'point-up', just under the surface of the ground, within 100 yards or so of an enemy installation.
If you're still undecided as to orgonite's effectiveness, try making or acquiring at least one of these units & find an ugly tower in your neighborhood (check http://www.ethericwarriors.com or the 'Cel-Towers In Our Daily Lives' document on my site http://groups.google.com/group/bellinghamorgone if you're not immediately familiar with which ones are the gnarly kind), plant your TB thereabouts, get a little ways away & then sit back & watch what happens over the next 15-20 minutes. The effects from 'tower-busting' supposedly aren't as strong as actively using an orgonite 'Chem-Buster', but you should be able to see *something* fairly quickly, as the emanations from the TB 'piggyback' & overtake the signals relayed by the Death-Tower, turning it into a standing orgone-transmitter all on its own.
A last word:
These devices are NOT pretty; they don't need to be. No one will see these (cross your fingers) but you & maybe me, depending on whether you make or acquire them. They're gonna go into the ground, or in a bush, or somewhere next to the highway.... They're not meant to be cosmetic; they're meant to be PRACTICAL.
Happy hunting.
[attachment=18]
I like to mix some metal & resin in a separate container & add the goop in stages, poking at it with a stick & tamping it down as I go to avoid air-bubbles. Even so, the bubbles are practically unavoidable; I have found that, while unsightly, if they aren't too big they don't make any significant difference in the device's performance.
First, I'll lay down a good base of the metal & resin, then push the crystal-assembly point-down into the clump & fill the rest of the glop down between the coil-windings---this is where the stick comes in handy---much easier than trying to wind the coil down into the goo.
[attachment=19]
Then, I'll fill the rest of the tube with some more glop, covering the top of the coil as I go, & tamp it down some more (being careful when packing it down that I don't cut through the tape); if you watch it carefully while the resin 'cooks', there will be about a 5 minute widow of time during which you'll be able to see bubbles & smoke percolating up through the already-hardened surface, like a witches' cauldron, & the mould will be hot to the touch. Now wait 4 or 5 hours for the stuff to 'breathe' & harden; if you bring it in too soon, you will overwhelm your household with noxious gasses.
[attachment=20]
Lastly, after peeling off the tape & picking off as much of the resin-spillage as will come, the TB's will still be sticky on the outside, so I cover them with a piece of a grocery-bag & tie them up with fishing-line. This is totally unnecessary in terms of the device's functionality; I just do it to facilitate travel in my jacket-pockets.
[attachment=21]
The outside can be painted, if camoflauge is desired for locations where burying them is impractical.
[attachment=22]
I like to bury them 'point-up', just under the surface of the ground, within 100 yards or so of an enemy installation.
If you're still undecided as to orgonite's effectiveness, try making or acquiring at least one of these units & find an ugly tower in your neighborhood (check http://www.ethericwarriors.com or the 'Cel-Towers In Our Daily Lives' document on my site http://groups.google.com/group/bellinghamorgone if you're not immediately familiar with which ones are the gnarly kind), plant your TB thereabouts, get a little ways away & then sit back & watch what happens over the next 15-20 minutes. The effects from 'tower-busting' supposedly aren't as strong as actively using an orgonite 'Chem-Buster', but you should be able to see *something* fairly quickly, as the emanations from the TB 'piggyback' & overtake the signals relayed by the Death-Tower, turning it into a standing orgone-transmitter all on its own.
A last word:
These devices are NOT pretty; they don't need to be. No one will see these (cross your fingers) but you & maybe me, depending on whether you make or acquire them. They're gonna go into the ground, or in a bush, or somewhere next to the highway.... They're not meant to be cosmetic; they're meant to be PRACTICAL.
Happy hunting.